Covered mold — often called silicone duplication molding — solves one specific sourcing problem: you need parts, but all you have is a physical sample and no drawings. It is the fastest route from a bare sample to functional parts, and it is also the process most often oversold, because its limits matter as much as its speed.
Here is how it works, where it genuinely fits, where it does not, and how duplication parts become the bridge to a production steel tool.
How Silicone Duplication Molding Works
A master — the sample, or a 3D-printed replica refined from it — is suspended in a frame, and liquid silicone is poured around it and cured into a flexible mold. Polyurethane or silicone resin is then cast or pressed into the cavity. The cycle repeats dozens of times before the silicone mold fatigues.
Two details decide the quality of the result. First, how the master is prepared: it is cleaned, inspected for wear or damage, and repaired if necessary, because the mold will faithfully copy every scratch it finds. Second, how the split is planned: the mold maker decides where the parting line goes and where air will be allowed to escape, which determines whether the cast part needs trimming and how much flash you will see.
Where Covered Molds Genuinely Fit
Legacy parts with lost tooling: a machine from a discontinued line needs a seal, and nobody has the drawing. Bridge production while a steel tool is being cut: you need parts now to keep a line running, and production-quality parts later.
Gaskets and pads with simple but irregular geometry: flat-ish parts that are awkward to draw but easy to cast. Validation batches of 10-100 pieces, where steel tooling cannot amortize — this is the sweet spot of the process.
Urgent repair and spare-part situations fit here too. When downtime costs more than the parts, a mold that can be ready in days changes the arithmetic entirely.
The Honest Limits
Dimensional fidelity is about ±0.2 mm: a silicone mold copies the master, but it also breathes under pressure and flexes during demolding. Surface quality inherits the master — including its scratches and its wear.
Material choice is limited. Cast polyurethane and silicone resins approximate rubber properties but never equal them: heat resistance, compression set and long-term aging all fall short of a vulcanized production compound. Compression set is the one that matters most, which is why duplication parts are not suitable for seals with tight compression requirements.
When Not to Use a Covered Mold
Do not use duplication parts as production parts for high-temperature service, dynamic sealing, or anything requiring certification documentation for the material. Do not use them where the seal must hold a defined compression over years, and do not use them where a customer audit will require a material certificate tied to a production compound.
The rule of thumb: duplication parts are excellent for validating fit, form and function, and for urgent replacements. They are not a substitute for a qualified production part in a critical application.
Economics and Lead Time
Duplication molds cost a fraction of steel tooling and run in days, which makes them ideal for validation batches. Compare them against the alternative honestly: for 20 pieces, the duplication route is usually faster and cheaper than any molded route; for 20,000 pieces, it is neither.
Duplication also has a diagnostic value that is easy to overlook. A duplicated part can be assembled, tested and even run in the field to confirm that the geometry is right — before anyone commits to a steel tool.
From Duplication Parts to a Production Tool
When volumes justify it, the sample is reverse-engineered into a proper drawing and a steel tool is cut. The duplication parts serve as the dimensional reference during that transition, and the drawing captures what the sample alone could not: tolerances, material specification, hardness, surface finish and inspection criteria.
The sequence matters. Measure the sample, agree the drawing with the customer, confirm the compound, then cut steel. Programs that skip the drawing step usually discover at first article that everyone had a different understanding of the same sample.
Common Mistakes
Copying a worn sample without measuring the wear first — the copy inherits the problem, and sometimes the copy is then used as the reference for the steel tool. Ignoring casting shrinkage, which differs between resins and can move a critical dimension. Assuming hardness will match: the casting resin has its own hardness, which may not equal the sample's. And using duplication parts in high-temperature service, where polyurethane castings reach their limit far earlier than a vulcanized rubber compound.
A subtler one: forgetting to check the master for a draft angle. If the original part was molded with draft, the copy will have it; if it was machined without draft, the silicone mold may tear on every cycle.
Inspection of Duplicated Parts
Treat duplicated parts as prototype parts with a documented report: dimensions against the agreed drawing or the measured sample, hardness of the casting, and a visual check against the master's condition. Where the part will be assembled into a sealing groove, verify the compression behaviour in the actual assembly rather than on the bench.
For parts that will later be produced in a steel tool, keep a signed sample from the duplication batch. It becomes the physical reference for first-article comparison.
Rubbrother's Role in This Route
Rubbrother's duplication mold route exists for exactly these situations: a sample in hand, no drawing, and a deadline. Duplication molds run in days, and the in-house mold shop and in-house testing laboratory keep both the sample measurement and the report under one roof. When volumes justify it, we reverse-engineer the sample into a proper drawing and cut a steel tool on 10 compression presses; the duplication parts serve as the dimensional reference. Quotations are returned within 24 hours, new-mold quotations within 7 days, and sampling takes 7-12 working days depending on mold complexity. Mold and sampling fees are refunded once the bulk order reaches the agreed volume, sample freight is paid by the buyer, MOQ is flexible, and the factory holds ISO 9001, ISO 14001 and IATF 16949. Third-party audits and video factory tours are welcome if you would like to see the process first.
