Blog2026-03-16

Shore A Hardness: How to Choose the Right Value

Shore A 20-80 covers most sealing and damping applications: 20-40 for soft seals and pads, 50-70 the general-purpose band, 70-90 for load-bearing parts. This article explains how hardness interacts with compression set, sealing force and damping, with typical values per application.

Hardness is the most quoted — and most misused — spec in rubber parts. It matters because it drives sealing force, compression behavior and damping, yet it is only one of three levers alongside compound and geometry. Buyers who try to fix a leak by ordering a harder compound usually receive a stiffer part that leaks again two months later; buyers who specify a single number without a tolerance band usually spend the next meeting arguing about a measurement.

This guide covers the Shore A bands that actually matter in practice, how hardness interacts with compression set and sealing force, how to write it on a drawing so that it can be measured, and the mistakes that cost the most time.

The Three Shore A Bands

Shore A 20-40: soft seals, cushioning pads, overmolded grips. Low force to seal and excellent conformability, but higher compression set — avoid for high-pressure gaskets. This is also the band where overmolding and tactile surfaces live, because soft compound flows into undercuts and thin ribs.

Shore A 50-70: the workhorse band — most O-rings (50-70A), general gaskets, dust seals, anti-vibration pads. Balanced sealing force and recovery, and the band with the widest choice of stocked compounds.

Shore A 70-90: load-bearing mounts, bumpers, structural pads, keyed precision parts. Higher load capacity and better creep resistance, but watch stress relaxation on long-term static loads, and remember that hard compounds seal only against well-finished mating surfaces.

Below Shore A 20 you are usually in sponge or gel territory (Shore 00 or OO scales). Above 90, polyurethane or a hard plastic is frequently a better engineering answer than forcing a rubber compound.

Hardness vs Compression Set, Sealing Force and Damping

Sealing force rises roughly with hardness: a 70A O-ring pushes back harder than a 50A ring of the same cross-section, so the gland must be sized for the squeeze the ring can actually generate. Static O-ring grooves typically run 15-25% squeeze — below that the seal weeps, above it compression set takes over as the failure mode.

Compression set is the permanent deformation left after the load is removed, measured to ASTM D395 or ISO 815. Harder compounds generally show lower compression set at the same temperature, which is why high-temperature static seals drift toward 70A — but a genuinely low-compression-set 50A compound will outperform a cheap filled 70A compound in the same groove.

Damping is a separate property, not a hardness level. Two compounds at 60 Shore A can differ noticeably in rebound. If the part's job is to absorb vibration rather than to seal, specify a rebound or tan delta target instead of assuming that softer always damps better.

Writing Hardness on a Drawing So It Can Be Measured

Two practical rules. First, hardness tolerance: ±5 Shore A is the industry norm — critical applications should be specified with a tolerance band, not a single number. Second, state the test method and specimen condition: ASTM D2240 or ISO 48-4, measured at 23°C after a defined conditioning time, on a stack at least 2 mm thick (6 mm preferred). A reading taken on a 1 mm section is wrong by several points, and the argument that follows costs more than the part.

Also record whether the value is nominal at 23°C, and what happens at service temperature. Rubber softens as it heats: a 70A compound at 23°C may measure around 60A at 100°C. For high-temperature seals, specify hardness at operating temperature, or accept a nominal value paired with a compression-set limit.

When a drawing arrives marked in IRHD, note that Shore A and IRHD read close to each other in the normal range but are not interchangeable standards. Ask which one the receiving inspection will use, and state the conversion in the drawing note.

What Temperature, Aging and Fillers Do to Hardness

Fillers make a compound harder and cheaper at the same time — and raise compression set while cutting elongation. When a quotation for a high-hardness part comes in unusually low, the first question is how much filler the compound carries and what it does to compression set after 70 hours at temperature.

Aging shifts hardness in both directions. Heat aging usually hardens silicone or EPDM parts as post-cure continues, while oil swelling softens NBR or FKM in service. Neither shows up in the incoming-inspection reading, so long-life parts should carry an aged-hardness limit as well as a fresh one.

One perception point matters commercially: silicone reads about 5 points softer in feel than natural rubber at the same measured hardness, and damping behavior differs too. When a customer compares two parts by hand, the durometer reading and the hand feel will disagree — write the number, then confirm on a sample.

Common Mistakes and a Pre-Spec Checklist

Frequent errors: specifying a single hardness value with no tolerance; measuring on a thin specimen; judging material by hand feel; raising hardness to cure a leak instead of reviewing squeeze and gland finish; and ignoring the low-temperature shift, where a 70A part behaves like 90A at -30°C.

Checklist before you specify: continuous and peak service temperature; contact media; static or dynamic sealing; required squeeze and groove dimensions; surface finish of the mating part; expected service life and compression-set limit; and hardness at both 23°C and operating temperature.

Changing hardness normally reuses the same tooling, which is why a hardness trial is one of the cheapest experiments available — but shrinkage differs slightly between compounds, so critical dimensions must be re-measured on the new samples.

When in doubt, order samples at two hardness levels — sampling takes 7-12 working days at Rubbrother, and mold fees are refundable on volume orders. The in-house testing laboratory reports hardness, dimensions and weight with every first article, the in-house mold shop keeps hardness-only changes fast, and Pantone color matching can be validated in the same sample round. Send a drawing with the tolerance band and the operating conditions, and you will receive a quotation within 24 hours that names a specific compound — not just a number.

Related